stevenrace
Joined 18 years ago
Karma
296
Submissions
140
Member since
Sep 8
Recent submissions
Comment · 9 years ago
What are you using for for networking/on board computing? The article mentions 2G is used in China - however here in the US such services are being depricated [1].
[1] https://www.att.com/esupport/article.html#!/wireless/KM10848...
Comment · 10 years ago
The resin has a low Tg (temp at which it turns goopy again) - somewhere around 500*F even for 'aerospace' stuff. Whereas recycling aluminum requires roughly double that temperature to begin to melt aluminum.
The carbon fiber is then chopped and used as reinforcement in other material likes plastics. SGL Group, who supplies/partners in production with BMW, even uses reclaimed and production waste in it's production process for the new 7-series.
A more technical breakdown and state of the industry can be found here: http://www.compositesworld.com/articles/recycled-carbon-fibe...
Comment · 10 years ago
"The idea for these soft bombs apparently grew out of a training accident in souther California. Military aircraft were dropping chaff - hundres of metallic strips used to confuse enemy radar. An airplane released its chaff near a power switching station and many of the strips fell onto a power switching station, blacking out a large area of Orange County."
- Weapons of Mass Casualties and Terrorism Responce Handbook - Charles Stewart MD FACEP
https://books.google.com/books?id=7ZnXZfwWwgcC&pg=PA221&lpg=...
referencing a Boston Globe article: May 4th 1999 page A27
---
I recall reading of another accident, but can't easily find the source.
Comment · 10 years ago
>Nobody's bothered to try to figure out how to create a
small-scale EMP without a nuclear blast
Targeting power grids 'the old fashioned way' in Desert Storm, Lockheed F-117As dropped a cluster bomb full of carbon graphite filaments (BLU-114/B). This shorted out power lines/transformers and destroyed 85% of Iraq's power grid. Later used in Serbia and accidentally in SoCal during testing [3].
---
[1] http://www.boeing.com/features/2012/10/bds-champ-10-22-12.pa...
[2] http://mil-embedded.com/3908-air-forceboeing-emp-weapon-movi...
Comment · 10 years ago
To mitigate issues with cold weather, 2nd generation Nissan Leaf battery packs with the 'cold weather package' include a 'battery warmer' between banks. This is controlled via the BMS which was already monitoring temperature with some thermistors. It's a resistive element like that used in heated seats or an electric blanket.
The Tesla battery is a liquid cooled battery and thus can be warmed via coolant that is heated by the inductive heater for the HVAC. Same for the GM Volt/Bolt.
Comment · 10 years ago
The Mendelmax 3 & Fusematic from Makers Tool Works are built in the USA and sourced from US suppliers. The guy behind it has done more for the RepRap mechanical bits, aside from Joeseph Prusa.
The Lulzbot mentioned below was based on the Mendelmax 1.5. This line of printers moved RepRap from a threaded rod construction to extruded aluminum. Also the first to have linear rails instead of steel rod+linear bearings. The new Mendelmax3 is a mix of laser cut parts and extrusions - and has required less service than any of my printers to date.
Comment · 10 years ago
While there isn't a specific section covering endnotes, they are interspersed sparingly as tonal changes in the narrator's voice. This effect is used in other readings of his works and is easy to follow.
Comment · 11 years ago
While that was designed in 1984, the US DoD had successfully tested laser weapons over a decade earlier:
'The first was in 1973 when the USAF shot down a winged drone at their Sandia Optical Range, New Mexico, using a carbon dioxide GDL and a gimballed telescope. Subsequently, in 1976, the US Army employed an electrically pumped HEL to destroy a number of winged and helicopter drones at the Redstone Arsenal in Alabama. The USN, in March 1978, then engaged and destroyed an Army TOW missile in flight' [1]
The first targets destroyed from an airborne platform (KC-135) were in 1979.
Comment · 11 years ago
The 'Waveglider' [1] by Liquid Robotics employs a variation of this. Tethered to a buoy on the surface, the main underwater vehicle is propelled forward by the wave's upward force acting on spring loaded foils.
[1] http://liquidr.com/technology/waveglider/how-it-works.html
Comment · 12 years ago
FWIW the CERT ('US Computer Emergency Readiness Team') report on the 19th [1] delves a bit deeper into the exploit methods.
If you search for the MD5 hashes of the code you can find code snippets and incidents where such code was used in the past (hacking attempts at DHS, etc). Even though none of these were '0-days' or written by those with ties to NK, the attribution seems to be based on such code reuse.
Comment · 12 years ago
Alternately, there is 'cool-retro-term':
Comment · 12 years ago
In passing he also mentions a Tumblr posting screenshots from scans. This appears to be the page: http://mainframesproject.tumblr.com/
Comment · 12 years ago
I suspect you'd still need 'supports' added when slicing - as often it's not so much gravity, but movement from the print head that causes things to go awry.
As for layer/bed adhesion. Even here on Earth, the RepRap MendelMax/Lulzbot [1] can print upside down. I imagine that's true for most of the units made from aluminum extrusions. And there have already been prints done in parabolic 'zero-g' flights using a Makerbot looking printer [2].
[1] http://download.lulzbot.com/TAZ/photos/upside_down/Lulzbot_p...
Comment · 12 years ago
Because it's fun.
To be fair, 250W on an ebike is 'not fun' or anywhere close to the legal limits in the US (750-1000W).
The happy spot seems to be 2500-5000W for most hub driven ebikes. I turned my bike down to 1000W this afternoon and couldn't imagine running anything less.
Endless-sphere [1] is the place to go if you're interested in eskateboards/ebikes with a bent towards DIY/highpower.
Comment · 12 years ago
Fascinating, thanks.
At what speed do you replay text->audio (ie realtime, 1.5x,2x,...)?
Lastly, if you disregard price is the braille 'refreshable display' a better experience?
murmurationprototyping [at] gmail.com