frowin

Hyperpolarization also allows for cheaper MRI scanners. With hyperpolarization, you achieve polarization (needed for SNR) without the need of big magnets (=expensive). Even in rich countries, MRI scanners reach their physical and technical limits. 3T magnets are already 7-figures and costs of bigger magnets will increase non-linearly. Moreover, with higher fields, side effects increase, too.

Out of curiosity, investment = crypto? I can relate a tiny bit.

Great explanation. Indeed, the "rotation/tumbling" is nothing to worry about. One of our biggest challenges is relaxation. The moment we polarize, the clock ticks. Usually, the time scope is around 15-90s. I'm in the field of para-hydrogen and built automated systems which carry out the chemical reactions, polarization transfers and sample cleaning. Many hyperpolarization experiments with para-hydrogen prefer nasty solvents as chloroform or methanol. It is a technical challenge to replace them by water within seconds. One of my favorite topics is Xenon hyperpolarization. It's very elegant, no cleaning required, no wet chemistry, and provides amazing lung scans.

I'm finishing my PhD in hyperpolarization (hopefully) soon. In my opinion, hyperpolarization will significantly contribute to early-stage diagnosis. We're designing machines, processes, and chemicals that create novel contrast agents for MRI, enabling the localization of cancer cells and even tracking their metabolism. For example, it's possible to inject hyperpolarized pyruvate and track its conversion to lactate. Essentially, this technique boosts the MRI/NMR signal of the contrast agent by up to 100,000-fold. When the contrast agent undergoes metabolism, it creates a unique signal footprint through chemical shift changes, which can aid in characterizing cancer.

As a scientist, I'm so glad that we're forced to publish all our primary/secondary data along with the publication itself. It's stored in a repository which is "locked" when the DOI (digital object identifier) is generated. Overall, the publishing process is tedious and frustrating, but this extra work is crucial and cases like this makes that very clear. However, in most of the recent cases you didn't even need to look at the data as even the publication itself shows the misconduct.

I don't see any problem here.

I think not. It keeps battery cycles low and is likely better than some other behavior. As far as I remember, batteries don't like to go way below 20% and don't like fast charging from 80% upwards. However, to my knowledge, it is wise to drain the battery 1-2 times a year so that the charging controller can calibrate. A way to do that is to type "yes" in your terminal (or 3-4 terminals) and wait, it will make the CPU run at 100%. After your MacBook shut off, leave it for some hours before you charge it again.

Or an SSD. Is easy and cheap these days.

It's not only a matter of aesthetics but bacteria etc. Your brush head collects a sh*tload of food waste (which you don't see with your eyes) and remains a bit wet after usage. Perfect substrate for some living organisms. If you have a microscope, feel free to have a closer look.

The brushes have this sensor for a reason. Too much pressure may harm your gum. The article talks about a ultrasound brush, no pressure required.

Clearly, he possesses considerable expertise, but it's puzzling why such a skilled individual would falter towards the end, resulting in poor solder joints on the 2.54mm pin headers. This isn't merely a question of aesthetics; these joints are susceptible to failure.

His work is commendable, but I would encourage him to either learn proper soldering techniques or, if he already possesses the skills, to take a moment to use some flux and clean up the joints. It's a simple process that takes just three seconds per joint.

I have this brush and would highly encourage you to swap the head when the brush asks you to do so, for the sake of your dental health.

We use Kanboard in our institute, but its UI/UX is among the worst I've experienced. It's reliable, but extremely unintuitive, causing people to avoid using it. However, it has potential.

It's kinda strange, I tried to sell my Flipper Zero and was wondering why people name them weirdly. As it turns out, ebay doesn't allow to sell it. If anyone has an idea where I can offer it (Germany, Europe), let me know.

in case the author is reading this:

I would suggest to add an affiliate tag to the Amazon link. I once heard that authors make more from the affiliate program than from the book itself. Maybe a modern anecdote but yeah... costs you nothing. As you don't get rich by the book itself, atleast you get some few dollars through the link!